National Institute of Technology Rourkela

राष्ट्रीय प्रौद्योगिकी संस्थान राउरकेला

ଜାତୀୟ ପ୍ରଯୁକ୍ତି ପ୍ରତିଷ୍ଠାନ ରାଉରକେଲା

An Institute of National Importance

All Publications

Saroj Kumar Patel

Professor
skpatel@nitrkl.ac.in

K. Tudu, S. Murugan, and S. K. Patel,"Experimental analysis of a di diesel engine fuelled with light fraction of pyrolysis oil", International Journal of Oil, Gas and Coal Technology, vol.11, no.3, pp.318-338, Inderscience, December 2016, 10.1504/IJOGCT.2016.074770       Article
S. Nigam, S. S. Mahapatra, and S. K. Patel,"Numerical modelling of sliding wear caused by pin-on-disk method over copper coated ABS plastic substrate", IOP Conference Series: Materials Science and Engineering, vol.149, no.1, IOP Publishing, September 2016, 10.1088/1757-899X/149/1/012079       Article
S. Nigam, S. K. Patel, and S. S. Mahapatra,"Sliding wear analysis of a metallic coating on ABS plastic substrate", Applied Mechanics & Materials, vol.852, pp.381-387, Trans Tech Publications, September 2016, 10.4028/www.scientific.net/AMM.852.381       Article
D. K. Sen, S. Datta, S. K. Patel, and S. S. Mahapatra,"G-resilient supplier selection in fuzzy environment: application potential of satisfaction function and distance based approach", in 4 th Asia Conference on Mechanical and Materials Engineering (ACMME), ACMME, Kuala Lumpur, Malaysia, December 2016       Inproceedings
D. K. Sen, S. Datta, S. K. Patel, and S. S. Mahapatra,"Fuzzy-TODIM for industrial robot selection", in 1st International Conference on Emerging Trends in Mechanical Engineering,, IEEE, Hyderabad, India, September 2016       Inproceedings
A. K. Mehar, S. S. Mahapatra, and S. K. Patel,"Fabrication, processing and assessment of mechanical behaviour of Hydroxyapatite (HAp) reinforced Polycarbonate (PC) Composite for bio-medical applications", Trends in Industrial and Mechanical Engineering, pp.84-90, Ethan Publishing, July 2016       Article
A. Das, A. Mukhopadhyay, S. K. Patel, and B. B. Biswal,"Comparative assessment on machinability aspects of AISI 4340 alloy steel using uncoated carbide and coated cermet inserts during hard turning", Arabian Journal of Science and Engineering, vol.41, no.11, pp.4531-4552, Springer 2016, 10.1007/s13369-016-2160-0       Article
K. Tudu, S. Murugan, and S. K. Patel,"Effect of diethyl ether in a DI diesel engine run on a tyre derived fuel-diesel blend", Journal of the Energy Institute, vol.89, no.4, pp.525-535, Elsevier 2016, 10.1016/j.joei.2015.07.004       Article
P. K. Mohanty and S. K. Patel,"Basic Statistics", Scientific Publusher, Ansari Road, Daryaganj, New Delh 2016       Book
A. Das, S. K. Patel, B. B. Biswal, and A. K. Pradhan,"Influence of various cutting fluids on machining forces in hard turning of 4340 alloy steel using uncoated cermet inserts", in Proceedings of 6th International & 27th All India Manufacturing Technology, Design and Research Conference (AIMTDR 2016), pp.1233-1237, December 2016       Inproceedings