S. Sarkar and S. Datta,"Machining Performance of Inconel 718 Under Dry, MQL, and Nanofluid MQL Conditions: Application of Coconut Oil (Base Fluid) and Multi-walled Carbon Nanotubes as Additives", Arabian Journal for Science and Engineering, vol.46, pp.2371-2395, Springer 2021, 10.1007/s13369-020-05058-5       Article

S. K. Sahu, J. Thrinadh, and S. Datta,"Parametric studies on SiC-abrasive jet assisted machining of alumina ceramics", Materials Today: Proceedings, vol.44, no.part 1, pp.1643-1652, Elsevier 2021, 10.1016/j.matpr.2020.11.823       Article

K. Pandey, S. P. Sahoo, and S. Datta,"Machining Behaviour of Inconel 825 under Distilled Water Based Minimum Quantity Lubrication", Materials Today: Proceedings, vol.44, no.part 1, pp.2386-2388, Elsevier 2021, 10.1016/j.matpr.2020.12.449       Article

K. Pandey and S. Datta,"Hot Machining of Difficult-to-Cut Materials: A Review", Materials Today: Proceedings, vol.44, no.part 1, pp.2710-2715, Elsevier 2021, 10.1016/j.matpr.2020.12.687       Article

S. P. Sahoo, S. Datta, T. Roy, and S. Ghosh,"Machining performance of Ti6Al4V under dry environment, pressurized air supply and water-MQL: analysis of machining-induced vibration signals and captured thermographs", Sadhana, vol.46, no.4, pp.2-22, Springer 2021, 10.1007/s12046-021-01738-6       Article

S. P. Sahoo, S. Datta, T. Roy, and S. Ghosh,"Machining Performance of Ti6Al4V under Dry Environment, Pressurized Air Supply and Water-MQL: Analysis on Machining- Induced Vibration Signals and Captured Thermographs", Sadhana, an Official Journal of the Indian Academy of Sciences, Springer, October 2021, 10.1007/s12046-021-01738-6       Article

S. P. Sahoo, S. Datta, T. Roy, and S. Ghosh,"Machining Performance of Ti6Al4V under Dry Environment, Pressurized Air Supply and Water-MQL: Analysis on Machining- Induced Vibration Signals and Captured Thermographs", Sadhana, an Official Journal of the Indian Academy of Sciences, Springer, October 2021, 10.1007/s12046-021-01738-6       Article

S. P. Sahoo and S. Datta,"Experimental Studies on Dry Machining Behavior of Ti-6Al-4V using Carbide, Cermet, and SiAlON Tools", Sadhana, an Official Journal of the Indian Academy of Sciences, Springer, November 2021, 10.1007/s12046-021-01767-1       Article

K. Pandey and S. Datta,"Dry Machining of Inconel 825 Superalloys: Performance of Tool Inserts (Carbide, Cermet, and SiAlON)", International Journal of Manufacturing, Materials, and Mechanical Engineering, vol.11, no.4, pp.26-39, IGI Global, October 2021, 10.4018/IJMMME.2021100102       Article

M. Rakesh and S. Datta,"Machining of Inconel 718 Using Coated WC Tool: Effects of Cutting Speed on Chip Morphology and Mechanisms of Tool Wear", Arabian Journal for Science and Engineering, vol.45, no.2, pp.797-816, Springer 2020, 10.1007/s13369-019-04171-4       Article